POINT 416 POLY FIX is a bi-component polyester styrene free chemical anchor for medium loads, CE marked and ETA assessed for use in different base materials as concrete, solid masonry and hollow bricks masonry.
It is certified for threaded rods to be used in non-cracked concrete from diameters M8 to M24, in solid masonry from diameters M8 to M16 and hollow masonry from diameters M8 to M12, also for rebars Ø8 mm to Ø12 mm to be used in solid masonry.
Due to its strong adhesion and ease of penetration into holes and hollow materials, the resin allows a secure attachment without expansion and without stresses in the base material, which allows you to make fixings close to the corners and edges of base material.
ETA (European Technical Assessments) updated according to the Construction Product Regulation 305/2011. ETA-15/0560: Assessment for uncracked concrete, Option 7, according to ETAG-001 for diameters from M8 to M16. The product is certified for fixing with variable anchorage depths. This means that the project engineer and the user have an high flexibility. Maximum embedment depth up to 20 times nominal threaded rod diameter. Loads for installation in dry and wet concrete. Certified service temperatures are in the ranges: -40°C/+50°C (T° max long period = 40°C). ETA-11/0396: Assessment for masonry according to ETAG 029 for fixings in solid bricks, perforated bricks and hollow bricks. Utilization possible even on masonry with temporary humidity present only during the product installation phase. The product is homologated for being used with a wide range of masonry (6 type of bricks), threaded rods (from M8 to M12) and sleeves (GC 12×80 – GC 15×85 – GC 20×85). Certified service temperatures are in the ranges -40°C/+40°C (T° max long period = +24°C) and -40°C/+50°C (T° max long period = +40°C). Base material temperature (concrete, bricks, etc…) for installation between 0° and +30°C. VOC according to the French Decree 2011-321 and according to the standard ISO 16000/EN 16516.
Cleaning:
Drill the hole and check it’s perpendicularity. Blow the hole with an appropriate pump blower (or compression air), clean the lateral surface of the hole with an appropriate steel brush, blow again in the hole until there is no dust and/or any residual material inside. We strongly recommend use of the steel brush to clean hole sides.
Opening:
Unscrew the front cup, pull-out the steel closing clip according to the following operations: 1) Insert the mixer in the eye of the plastic extractor. 2) Pull the extractor to unhook the steel closing clip of the foil. After that, screw on the mixer and insert the cartridge in the gun. Use protections for hands and face.
Cartridge preparation:
Use the correct dispenser
Before starting to use the cartridge, eject a first part of the product, being sure that: 1) Trough the mixer (transparent) see that the flux of product is compound of the part A (white color) and of part B (black color). 2) The two components are completely mixed. The complete mixing is reached only after that the product, obtained by mixing the two component, comes out from the mixer with an uniform color. Now the cartridge is ready to be used.
Injection:
1) Inject resin into the hole up to fill it 2/3rds. In hollow bricks use the plastic sleeve and inject the resin inside.
2) Before insert the rod, verify that the element is dry and free oil and other contaminants. Insert threaded stud turning back and forth to avoid presence of air in the fitted hole.
3) For the installation and the following anchor load phase, respect the open time and curing time detailed in the technical data sheet and in the label of the product.
4) Before to load the anchor, check the hardened of the product.
5) The cartridge can be used again screwing the cup and replacing the mixer. Remember to eject a first part of the product, see point 3.
Store in a vertical position in a dry place at a temperature between +5 °C and +30 °C. Expiry date – 15 months from the date of manufacture, in compliance with the storage rules. Quantity in a box – 15 pcs. Quantity in the palette – 960 pcs. Unit weight – 0.570 kg. Transport temperature from +5°C to +30°C.
